CAS LP-II Manuel de service Page 42
- Page / 89
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10 Printer Settings
34
< CAL: PRINTER HARDWARE SETTINGS >
1. PRINTER SENSORS 5. ADJUST FEED LENGTH
2. PRINT SPEED 6. AUTO THRESHOLD
3. PRINTER ODOMETER 7. REPORT SETTINGS
4. LABEL TYPE
< CAL: PRINTER SENSORS >
1. GAP/PEEL CALIBRATE
2. FINE GAP ADJUST
3. FINE PEEL ADJUST
< CAL: PRINTER SENSOR CALIBRATION >
Load Printer With Gapped Labels
Press any key when ready.
GAP= 100 PEEL= 151
< CAL: PRINTER SENSOR CALIBRATION >
The Printer will calibrate sensors
and print threshold values.
Press any key when ready.
GAP= 100 PEEL= 151
10.1 Printer Hardware Settings Menu
Once at the CAL Main menu
screen, press the 4 key. The
Printer Hardware Settings Menu
screen will appear as follows.
10.2 Printer Sensors
At the Printer Hardware Settings
Menu screen, press the 1 key for
Printer Sensors. The Printer Sensors
Menu screen will then appear as
follows:
Gap/Peel Calibrate: This is an
automated process that
calibrates both sensors. Please
make sure that there are non-continuous labels in the printer, that the labels are installed properly, and
that the print head is locked down. Using continuous labels will not calibrate the Gap sensor.
Fine Gap Adjust: This is a manual process that allows you to change the Gap sensor threshold value
directly.
Fine Peel Adjust: This is a manual process that allows you to change the Peel sensor threshold value
directly. This process also lets you actively test your setting.
Gap Sensor: This is the sensor that is used to sense the spaces between the labels (gaps.) It is
responsible for top-to-bottom alignment of your print.
Peel Sensor: This is the sensor that is used to sense if there is a printed label waiting to be picked up by
the user. If there is a printed label waiting to be picked up, this sensor will prevent another label from
printing. It will display an error message on the top right of the screen: “PEEL OFF”.
10.2.1 Gap/Peel Calibrate
At the Printer Hardware Settings Menu
screen, press the 1 key for Printer Sensors.
The Printer Sensors Menu screen will then
appear. At the Printer Sensors Menu
screen, press the 1 key for Gap/Peel
Calibrate. You will see the following
screen:
Once ready, press any key.
The printer will then feed out several labels
and then print the threshold values.
- Service Manual 1
- Attention: 3
- Disclaimer: 3
- Table of Contents 4
- 15 Installing Options 6
- 16 Troubleshooting 6
- 17 Diagrams 6
- 18 Part's List 6
- 1 (ONE) YEAR 7
- 1.1 Introduction 9
- 1 General 10
- 1.3 Dimensions 11
- 2 Unpacking and Assembly 12
- 2.1 Unpacking 12
- 2 Unpacking and Assembly 13
- 3 Proper Operation 14
- 3.2 Leveling and Location 15
- 4.1 Scale Overview 17
- 4 Nomenclature 17
- This is PLU Commodity Nam 18
- 4.3 Printer 19
- 4 Nomenclature 23
- 5 Getting Started 24
- MAKE SURE YOU HAVE DONE 25
- THE ADJUSTMENTS AT POINTS 25
- 1, 2, AND 3 BEFORE YOU LOCK 25
- THE PRINT HEAD 25
- 5 Getting Started 26
- 6 Calibration Mode 28
- 0 3569 29
- Calibration Passed! 30
- 7.4 Gravity Constant 31
- 8 System Options 33
- 8.1 Weight Options 33
- 8.1.1 Capacity & Units 33
- 8.1.2 Tare Options 34
- 8.2.3 Report Settings 38
- 8.3 Keypad Options 38
- 8.4 Clear Memory 39
- 8.5 Select Country 40
- 9 Digital Filtering 41
- 9.1 Digital Filter Settings 41
- 10.2 Printer Sensors 42
- 10.2.1 Gap/Peel Calibrate 42
- 10.3 Print Speed 43
- 10.4 Printer Odometer 44
- 10.5 Label Type 44
- 10 Printer Settings 45
- 10.6Feed Adjust 46
- 10.7 AUTO THRESHOLD 46
- 10.8 REPORT SETTINGS 46
- 11.1 Setting Up a Network 47
- 12369 0 0 49
- 12 Self Test Mode 50
- 12.4 Keyboard Test 50
- 12.5 Printer Test 51
- 12.9 Serial Port Test 53
- 12.10 Firmware Versions Test 53
- 13 Audit Trails 54
- 14.2 Removing the Upper Case 55
- 14.3 Main PCB Replacement 57
- Replacement 63
- 16.1 Troub 65
- 16.2 Additional Errors 67
- 17 Diagr 68
- 17.1 System Block Diagram 68
- MAIN BOARD 69
- 6100-PL2-0001-A 70
- 6100-PL2-0003-0 : ETHERNET 71
- 18 Part’s List 75
- 18.1 ELECTRICAL 75
- 18.2 AL MECHANIC 80
- 18.3 MECHANISM 82
- Appendix A-Country Codes 85
- GRAND TOTAL 87
- Appendix B-Label Formats 88
Produits connexes et manuels pour Balance de cuisine CAS LP-II
Balance de cuisine CAS LP-II Spécifications
(54 pages)
(54 pages)
Balance de cuisine CAS DL-60 Spécifications
(98 pages)
(98 pages)
(48 pages)
(59 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels